- 您现在的位置：买卖IC网 > Sheet目录985 > ISL97632IRTZ-EVALZ (Intersil)EVAL BOARD FOR ISL97632IRTZ
ISL97632
Detailed Description
The ISL97632 uses a constant frequency, current mode
control scheme to provide excellent line and load regulation.
There are three OVP models for driving 3, 4, and 7 LEDs
(3.5V/20mA type) and their OVP thresholds are set at 14V,
18V, and 26V respectively. The ISL97632 operates from an
input voltage of 2.4V to 5.5V and ambient temperature
from -40°C to +85°C. The switching frequency is around
1.45MHz and allows the driver circuit to employ small LC
components. The forward current of the LED is set using the
R SET resistor. In the steady state mode, the LED current is
PWM input, as the part resets to 0 whenever EN is low. To
resume previous setting, the device needs to be
reprogrammed.
Output Disconnect
The ISL97632 features a FBSW feedback disconnect switch
that can be used in between the LED and R SET for an
optional short-circuit protection. For example, the user may
build an external short circuit detection to monitor the V OUT .
If the V OUT goes low due to one or more LEDs which are
shorted, the circuit can release the EN and FBSW switch to
disconnect the LEDs.
I LED ( S ) = -------------------- = --------------------------------------------------------
given by Equation 1:
V FB ( S ) 9.8mV + 5.68mV × S
R SET R SET
(EQ. 1)
Components Selection
The input capacitance is typically 0.22μF to 4.7μF. The
output capacitor should be in the range of 0.22μF to 1μF.
0.8 ? V IN
where S is the 5-bit Serial Interface Setting or Digital code
from 0 to 31 programmed in the XSD single-wire interface.
The default setting is 0 and the VFB is at minimum.
Dimming Control
The ISL97632 powers up to provide minimium current. By
programming the digital code with the Intersil’s 1-Wire XSD
interface as shown in Figure 1, the current can be changed
X5R or X7R type of ceramic capacitors of the appropriate
voltage rating are recommended.
When choosing an inductor, make sure the average and
peak current ratings are adequate by using Equations 2, 3
and 4 (80% efficiency assumed):
I LED ? V OUT
I LAVG = --------------------------------- (EQ. 2)
I LPK = I LAVG + --- ? Δ I L
Δ I L = ---------------------------------------------------
linearly with the digital code from 0 to 31. Figure 6 shows
LED current versus the programming codes.
Overvoltage Protection
The ISL97632 comes with overvoltage protection. The
OVP trip points are at 14V, 18V, and 26V for
1
2
V IN ? ( V OUT – V IN )
L ? V OUT ? f OSC
Where:
(EQ. 3)
(EQ. 4)
ISL97632IRT14Z, ISL97632IRT18Z, and
ISL97632IRT26Z respectively. The maximum numbers of
LEDs and OVP threshold are shown in Table 1. When the
device reaches the OVP, the LX stops switching, disabling
the boost circuit until V OUT falls about 7% below the OVP
threshold. At this point, LX will be allowed to switch again.
The OVP event will not cause the device to shutdown .
TABLE 1.
? Δ I L is the peak-to-peak inductor current ripple in Amps
? L is the inductance in H.
? f OSC is the switching frequency, typically 1.45MHz
The ISL97632 supports a wide range of inductance values
(10μH~82μH). For lower inductor values or lighter loads, the
boost inductor current may become discontinuous. For high
PART NO.
ISL97632IRT14Z
ISL97632IRT18Z
ISL97632IRT26Z
OVP
14V
18V
26V
MAX NO. OF
LEDS
3
4
7
MAX ILED
70mA
50mA
30mA
boost inductor values, the boost inductor current will be in
continuous mode.
In addition to the inductor value and switching frequency, the
input voltage, the number of LEDs and the LED current also
affect whether the converter operates in continuous
conduction or discontinuous conduction mode. Both operating
There are three OVP options. The 3 LEDs application
should use the 14V OVP device. The 7 LEDs application
should use the 26V OVP device. An output capacitor that is
only rated for the required voltage range can therefore be
used which will optimize the component costs in some
cases.
Shut-Down
An active high EN pin is normally on but this pin can be used
as a shutdown power saving function or zero brightness
setting. When taken low the EN pin places the ISL97632 into
power down mode down where the supply current is
reduced to less than 1μA. The EN pin cannot be used as
6
modes are allowed and normal. The discontinuos conduction
mode yields lower efficiency due to higher peak current.
Compensation
The product of the output capacitor and the load create a
pole while the inductor creates a right half plane zero. Both
attributes degrade the phase margin but the ISL97632 has
an internal compensation network that ensures the device
operates reliabily under the specified conditions. The
internal compensation and the highly integrated functions of
the ISL97632 make it a design friendly device to be used in
high volume high reliability applications.
FN9239.3
March 22, 2010
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ISL97671IRZ-EVALZ
BOARD EVALUATION FOR ISL97671
ISL97684IRTZEVALZ
EVAL BOARD LED DRIVER
ISL97801BOOSTEVALZ
EVAL BOARD FOR ISL97801
ISLA118P50IR72EV1Z
EVAL BOARD FOR ISLA118P50IR74
ISLA224IR72EV1Z
BOARD EVALUATION FOR ISLA224P
ISPTPKIT
SCREW KIT TAMPER RESISTANT 9PCS
ITCSN-0400-25-U
HEATSHRINK ITCSN 2/5" X 25'
JC2AF-TM-DC24V-F
RELAY GEN PURPOSE DPST 10A 24V
相关代理商/技术参数
ISL97634ART26Z-TK
制造商:Intersil Corporation 功能描述:
ISL97634IRT14Z
制造商:Intersil 功能描述:White LED Driver with PWM Dimming(3 LED)
ISL97634IRT14Z-T
功能描述:IC LED DRIVR WHITE BCKLGT 8-TDFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C
ISL97634IRT14Z-TK
功能描述:IC LED DRIVR WHITE BCKLGT 8-TDFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C
ISL97634IRT18Z
制造商:Intersil 功能描述:White LED Driver with PWM Dimming(4 LED)
ISL97634IRT18Z-T
功能描述:IC LED DRIVR WHITE BCKLGT 8-TDFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C
ISL97634IRT18Z-TK
功能描述:IC LED DRIVR WHITE BCKLGT 8-TDFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C
ISL97634IRT26Z-T
功能描述:IC LED DRIVR WHITE BCKLGT 8-TDFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C